Archive for August, 2015

July Greenland Trip

August 29th, 2015

Made a quick trip to Greenland for three days in July to work on some equipment there.  I did not get on the air due to work activities and operation of the incoherent scatter radar whose modulator trashes the HF bands if you’re close to it (i.e., same building).  A few photos, though.  These were all shot with an iPhone 5s, nothing fancy.

50-MHz transverter update (Psst! Newark has cheap 22-MHz crystals)

August 29th, 2015

A few years ago, I built a 50-MHz transverter to operate 6m with my Kenwood TS-930Ses.  I subsequently replaced the two 930s with an Elecraft K3/100 and Elecraft K2/100.  The K3 has 6m and I sold off my TS-700S (and my 6m Mirage brick amplifier) to help finance the internal 2m board for the K3.  The problem with this arrangement is that I can’t be on 6m and 2m at the same time.  I recently assembled and added the SSB board and  transverter interface to my K2 (no time to blog about this but they were straightforward additions like everything from Elecraft), now making it an attractive IF for the 6m transverter (and the Microwave Modules 432 transverter I have on the shelf and the 222-MHz transverter I plan to build sometime).xvtr_50

Enter the problem: Because I was thrifty about building the transverter at first, I had used an inexpensive and widely-available 24-MHz crystal for a 26-MHz IF.  The TS-930S happily worked here (by the way, pro-tip: A lot of guys say that they liked to have the wideband transmit mods on their HF rigs so they could have a wideband signal source for testing/transverters/etc.  The TS-930S will give you a low-level TX out anywhere through the transverter port, even if you don’t have the mod.  Well, at least my PIEXX-equipped 930 did).  However, the K2 only allows a select set of transverter IF bands to be used natively.  Good fortune shone upon my endeavors when I did a quick Google search for 22-MHz crystals and one actually popped up at Newark/Element14 (part number is 86R1720, get ’em while they’re hot)!  Even better news was that it was on closeout for 12 cents apiece!  I splurged and bought five, along with some other parts for another project or two I’ll post about eventually.

I carefully peeled back a layer of dead-bug components, extracted the 24-MHz crystal, and replaced it with the new 22-MHz variety, sacrificing only one 4.7-k resistor, an easily-replaced stock item at K8GU.  The LO came up about 5.4 kHz low and I couldn’t peak it any higher.  So, I’ll either have to futz around with the loading of the crystal or (more likely) load an offset in the K2’s transverter band entry for 6m.

LO_22

The local W3APL beacon popped up at 28.0694 MHz, which is consistent with the offset I observed above.  Now, I just have to get the other interfacing juju worked out to get the K2 to properly command the transverter to transmit and feed it the proper drive level.

Converting the HP ESP120 Power Supply

August 23rd, 2015

Quick notes on converting the HP ES120 2950-watt blade server power supply to run “48-volt” amateur radio amplifiers.  The power supply I have has a slightly different in configuration from the one described by W8ZN on the K8GP site.

hp_001

I picked up the power supply on good terms at Dayton some years ago and finally managed to get around to hooking it up after I put two 240-volt, 20-amp circuits in my shack this spring/summer.  I used a molded air conditioner extension cord with the female end cut off to attach it to the wall.  Hot-ground-hot is the wiring on the AC input side.  On the output, there is a jumper block and two pairs of blade connectors, with one pair being positive and the other negative, strapped together.  In the middle of the output there is a jumper block.

hp_002

Here is where the steps differ from the W8ZN steps:  instead of shorting two pairs of pins together, this power supply requires three in a line to be shorted together.  It’s visible in the photo below, I think.  The center row.

hp_003

I’m getting 51.4 volts unloaded.  Load will be described in the future as it comes to be…